A drawing records what a part should be. A tolerance, a material callout and a surface finish remain statements of intent until a real part, made on the real production process, is measured against them. The gap between intent and result is where costly surprises start, and in aerospace the stakes include safety of flight. The first part made on a new process is where a manufacturer can find those surprises before a full run depends on it.
What is first article inspection?
First article inspection (FAI) is a documented verification that a part or assembly made with the intended production processes meets its engineering and design requirements.
The International Aerospace Quality Group (IAQG) owns the 9102 First Article Inspection Requirement, published as SAE AS9102. Its FAI FAQ describes the value this way: "The value of the First Article Inspection is to validate that the product realization processes are capable of producing parts and assemblies that meet engineering, design requirements." Here, product realization processes means the processes that turn a design into a finished part.
In practice, a manufacturer builds the part with the tooling, materials and methods planned for the run, then measures every characteristic the design requires and records the result. The part might be a machined bracket, a molded housing or a wiring assembly. What matters is the process behind it. If the first article conforms, the process has shown it can produce conforming parts. If it does not, the problem surfaces at the start of production rather than after a full run.
What a first article proves about a manufacturer's process
The FAQ states that "A well planned and executed FAI will provide objective evidence that the manufacturer's processes can produce compliant product and that they have understood and incorporated requirements." That sentence carries two separate proofs.
Proof of capability
The first proof is that the process can produce conforming product. The FAQ lists the outcomes FAI is intended to deliver:
- Reduce future risks and total costs.
- Help ensure safety of flight.
- Reduce the costs and production delays that come from nonconforming product.
- Identify production processes that cannot make conforming parts, then start and verify corrective actions.
Proof of understanding
The second proof is that the manufacturer read the requirements correctly and carried them into its manufacturing planning and purchasing documents.
Evidence planned before the first part is made
The FAQ says an organization should plan FAI activities prior to the first production run, covering the activities to be performed and the organizations responsible. Planning also settles:
- what evidence each characteristic needs
- which approved material, process and laboratory sources apply
- which part-specific gages and tooling are identified, qualified and traceable
Where a first article stops being proof
A first article is evidence about a specific moment. Among the outcomes the FAQ lists is "assurance of product conformance at the start of series production and after changes as outlined in this standard." Read that way, a first article has three limits.
It is not an acceptance decision
A first article report is not a product acceptance document, a point Revision C of the standard clarified. It records what was found and does not stand in for acceptance of product.
It covers one item at a time
Each item needs its own first article, so one part's result cannot vouch for another.
It speaks for the process as it was
Once tooling, sources or methods move, the original evidence may no longer describe the process in use.
When a process change means inspecting again
Because a first article speaks for the process as it was, a change to that process reopens the question. Inspections are full or partial, and Form 1 records which one was done and why. The FAQ gives concrete cases:
- A lapse in production of two or more years: an FAI is required for any characteristics that may be impacted by the inactivity, and a procedure should record the rationale when a full FAI is not performed.
- A change of supplier for a process specified on the drawing: a partial FAI covering the processes or characteristics moved.
- An alternate approved by engineering (an approved substitute): a partial or full FAI would generally be required, with the rationale documented when the determination is that none is needed.
- A change to how a characteristic is inspected, such as a different inspection tool: an FAI, complete or partial, for the changed inspection.
What each of the three AS9102 forms records
The evidence reaches a customer as the first article inspection report (FAIR). The report is built from three forms, and a separate post covers how AS9102 applies in manufacturing in more detail. Each form covers a different kind of accountability.
Form 1: part number accountability
Form 1 answers which part is being inspected. It identifies it with detailed part information.
Form 2: product accountability
Form 2 answers what the part was made from and how. It documents the materials and processes used to produce the first article.
Form 3: characteristic accountability
Form 3 answers whether every requirement was checked. It verifies the required characteristics, such as performance and dimensions, against the first article.
Ballooning means marking each requirement on a drawing with a numbered balloon so measurements can be traced back to it.
First article inspection vs PPAP: which question each one answers
Automotive supply chains use the Production Part Approval Process (PPAP), a framework distributed by the Automotive Industry Action Group (AIAG), for a related purpose. The table sets the two side by side, drawing on the FAQ and the AIAG PPAP manual (Fourth Edition, effective June 1, 2006).
| Point of comparison | First article inspection | PPAP |
| Question it answers | Can this process make a part that meets the design requirements? | Can this process keep making conforming parts at the production rate the supplier quoted? |
| Evidence submitted | A first article, measured against each design characteristic and recorded on the three AS9102 forms. | Parts from a significant production run of one to eight hours and at least 300 consecutive parts, unless the customer specifies otherwise. |
| When it applies | Planned before the first production run and revisited after changes as outlined in the standard. | For a new part or product, a correction to a previously submitted part, or an engineering change to design records, specifications or materials. |
| Standard and home sector | IAQG 9102 (published as SAE AS9102), used mainly in aviation, space and defense. | AIAG PPAP manual, used in the automotive supply chain. |
The first article gives early proof that the process can make the part, and a production run shows whether that holds at rate.
Quick answers on scope, failed inspections and buying the standard
Does first article inspection apply only to aerospace?
No. 9102 was written primarily for aviation, space and defense, yet other sectors can use it where a standardized FAI process is needed. Automotive supply chains commonly use PPAP, covered above, for a related purpose. The FAQ adds that the standard does not cover every instance an organization may meet or how the organization is to comply, so each organization documents its own FAI process.
What happens when a first article does not conform?
The nonconformance is documented in the report, and Form 1 records whether the report contains one. The FAQ adds that a part that fails inside an assembly stands on its own and needs its own FAI.
Where can the 9102 standard be bought?
9102 can be purchased in many languages from approved publishers such as SAE, SJAC and ASD-STAN. The standard contains the instructions for completing each form field, and the FAQ advises organizations to keep an internal procedure that defines their method.
Treat the first article as a claim you can defend later
Read as evidence, a first article is a claim made at the start of production: this process can make this part to these requirements. The claim is only as strong as the planning behind it and the discipline to reopen it when the process changes. When a supplier, tool or alternate changes, a team that planned its first article as evidence can say which results still hold and which do not.